Corner Chamfer End Mills

Corner Chamfer End Mill 8 mm Milling Dia Carbide TiAlN Non-Coolant Through Straight Metric 45 Degrees 0.4 mm 19 mm

Corner Chamfer End Mill 5 mm Milling Dia Carbide TiAlN Non-Coolant Through Straight Metric 45 Degrees 0.3 mm 13 mm

Corner Chamfer End Mill 4 mm Milling Dia Carbide TiAlN Non-Coolant Through Straight Metric 45 Degrees 0.2 mm 11 mm

Corner Chamfer End Mill 6 mm Milling Dia Carbide TiAlN Non-Coolant Through Straight Metric 45 Degrees 0.4 mm 13 mm

Corner Chamfer End Mill 3 mm Milling Dia Carbide TiAlN Non-Coolant Through Straight Metric 45 Degrees 0.2 mm 8 mm

Corner Chamfer End Mill 2 mm Milling Dia Carbide AlTiN Non-Coolant Through Straight Metric 45 Degrees 0.3 mm 24 mm

Corner Chamfer End Mill 10 mm Milling Dia Carbide AlTiN Non-Coolant Through Straight Metric 45 Degrees 0.2 mm 20 mm

Corner Chamfer End Mill 6 mm Milling Dia Carbide AlTiN Non-Coolant Through Weldon Flat Metric 45 Degrees 0.1 mm 13 mm

Corner Chamfer End Mill 16 mm Milling Dia Carbide AlTiN Non-Coolant Through Straight Metric 45 Degrees 0.3 mm 18 mm

Corner Chamfer End Mill 8 mm Milling Dia Carbide AlTiN Non-Coolant Through Straight Metric 45 Degrees 0.2 mm 16 mm

Corner Chamfer End Mill 5 mm Milling Dia Carbide AlTiN Non-Coolant Through Straight Metric 45 Degrees 0.1 mm 10 mm

Corner Chamfer End Mill 6 mm Milling Dia Carbide AlTiN Non-Coolant Through Straight Metric 45 Degrees 0.1 mm 12 mm

Corner Chamfer End Mill 4 mm Milling Dia Carbide AlTiN Non-Coolant Through Straight Metric 45 Degrees 0.1 mm 8 mm

Roughing End Mill 0.375 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.02 in 1 1/2 in

Roughing End Mill 0.625 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.03 in 2 in

Roughing End Mill 0.75 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.03 in 2 1/4 in

Roughing End Mill 0.3125 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.02 in 1 3/8 in

Roughing End Mill 0.625 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.03 in 2 in

Roughing End Mill 0.3125 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.02 in 1 3/8 in

Roughing End Mill 0.25 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.02 in 1 1/4 in

Roughing End Mill 0.375 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.02 in 1 1/2 in

Roughing End Mill 0.625 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.03 in 1 1/4 in

Roughing End Mill 0.3125 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.02 in 5/8 in

Roughing End Mill 0.25 in Milling Dia Carbide WXL Non-Coolant Through Straight Inch Not Applicable 0.02 in 1 1/4 in